View QPP-003_1299996.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

QuikPAC Module Data
General description:
The QPP-003 QuikPACTM RF power module is an impedance matched Class AB amplifier stage designed for use in the driver or output stage of linear RF power amplifiers for cellular base stations. The power transistor is fabricated using Xemod's advanced design LDMOS process. The gate terminal is connected directly to the control voltage pin, allowing direct control of the bias. The user must supply the proper value of VGS to set the desired quiescent current.
QPP-003 60W, 869-894 MHz Class AB Power Stage
Features:
Single Polarity Operation Matched for 50 RF interfaces XeMOS FET Technology Stable Performance QuikPAC System Compatible QuikClip or Flange Mounting
Standard Operating Conditions
Parameter
Frequency Range Supply (Drain) Voltage Bias (Gate) Voltage Bias (Gate) Current, Average RF Source & Load Impedance Load Impedance for Stable Operation (All Phases) Operating Baseplate Temperature Output Device Thermal Resistance, Channel to Baseplate
Symbol F VD VG IG
VSWR TOP jc
Min
869 26.0
Nom
28.0 3.6
Max
894 32.0 2.0
Units
MHz VDC VDC mA Ohms
50 -20 1.1 10:1 +90
C C/W
Maximum Ratings
Parameter
Supply (Drain) Voltage Control (Gate) Voltage, VDD = 0 VDC Input RF Power Load Impedance for continuous operation without damage Output Device Channel Temperature Lead Soldering Temperature Storage Temperature Symbol VDD VG PIN VSWR Value 35 15 5 3:1 200 +190 -65 to +150 Units VDC VDC W C C C
TSTG
Performance at 28VDC & 25C
Parameter
Supply (Drain) Voltage Quiescent Current (total) (1) Power Output at 1 dB Compression (single tone) Gain at 12W PEP (two tone) Gain Variation over frequency at 12W Output (two tone) Input Return Loss (50 Ref) at 12W PEP (two tone) Drain Efficiency at 60W Pout (single tone) Drain Efficiency at 60W PEP (two tone) 3 Order IMD Product (2 tone at 60W PEP;1 MHz spacing)
rd
Symbol VD1,2 IDQ P-1 G G IRL
Min
27.5 540 60 14.0 12.0 40 30
Nom
28.0 600 70 15.0 0.3 14.0 45 32 -28
Max
28.5 660
Units
VDC mA W dB
0.5
dB dB % %
-26
dBc
XEMOD RESERVES THE RIGHT TO MAKE CHANGES TO THIS SPECIFICATION WITHOUT FURTHER NOTICE. BEFORE THE PRODUCT DESCRIBED HERE IS WRITTEN INTO SPECIFICATIONS OR USED IN CRITICAL APPLICATIONS, THE PERFORMANCE CHARACTERISTICS SHOULD BE VERIFIED BY CONTACTING XEMOD.
Xemod QuikPAC Data QPP-003
www.xemod.com
Rev A (11-21-00)
Page 1 of 2
Performance at 28VDC & 25C (continued)
Parameter
IMD Variation - 100 kHz to 25 MHz tone spacing 2
nd rd
Symbol
Min
Nom
1.0 -35 -55
Max
2.0
Units
dB dBc dBc ns degrees
Harmonic at 60W Pout(single tone)
3 Harmonic at 60W Pout(single tone) Group (Signal) Delay Transmission Phase Flatness
d
3.6 0.5
Notes:
This QuikPAC module requires an externally supplied gate voltage (VGS) on each gate lead (pins 1 and 5) to set the operating point (quiescent current- IDQ) of the power transistors. VGS may be safely set to any voltage in the range listed in the table. This permits a wide range of quiescent current to be used. Since the operating characteristics of the module will vary as IDQ changes, the bias setting will depend on the application. The data provided in the Performance section of this data sheet was obtained with IDQ set to a value within the range listed (a nominal value 10%). This particular value was chosen to optimize gain, IMD performance, and efficiency simultaneously. Gate voltage must be applied coincident with or after application of the drain voltage to prevent potentially destructive oscillations. Bias voltages should never be applied to a module unless it is terminated on both input and output. The VGS corresponding to a specific IDQ will vary from module to module and may vary between the two sides of a dual RF module by as much as 0.10 volts. This is due to the normal die-to-die variation in threshold voltage of LDMOS transistors. Since the gate bias of an LDMOS transistor changes with device temperature, it may be necessary to use a VGS supply with thermal compensation if operation over a wide temperature range is required. Internal RF decoupling is included on all bias leads. No additional bypass elements are required, however some applications may require energy storage on the drain leads to accommodate time-varying waveforms. The RF leads are internally protected against DC voltages up to 100V. Care should be taken to avoid video transients that may damage the active devices.
Package Styles
This model is available in both B1 (H10536) and B1F (H11029) package styles. Style B1F is shown for reference. Please see the applicable outline drawing for specific dimensions.
Xemod QuikPAC Data QPP-003
www.xemod.com
Rev A (11-21-00)
Page 2 of 2

▲Up To Search▲

Price & Availability of QPP-003

	To Download QPP-003 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .